DCAudioDIY.com

DC Area Audio DIYer's Community
It is currently October 31st, 2024, 8:17 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 393 posts ]  Go to page Previous  1, 2, 3, 4, 5, 6 ... 40  Next
Author Message
PostPosted: January 27th, 2016, 1:24 pm 
Offline
User avatar

Joined: January 13th, 2016, 9:14 pm
Posts: 870
The second set of ChipAmps is being built and being tested for the planar OB section.

The full servo bass columns will look like this when all the 12' drivers are installed. Just four more to buy and install.


Attachments:
WP_20160125_003.jpg
WP_20160125_003.jpg [ 361.64 KiB | Viewed 78294 times ]
Top
 Profile  
 
PostPosted: January 27th, 2016, 1:46 pm 
Offline
User avatar

Joined: December 14th, 2013, 2:19 pm
Posts: 985
Awesome!


Top
 Profile  
 
PostPosted: January 27th, 2016, 2:12 pm 
Offline
Site Admin
User avatar

Joined: February 28th, 2013, 10:38 am
Posts: 1705
Stuart Polansky wrote:
My electrons are bigger, stronger and faster than your electrons
!


Yeah, but mine are smarter ;)

_________________
I can explain it to you, but I can’t understand it for you.


Top
 Profile  
 
PostPosted: January 27th, 2016, 3:09 pm 
Offline
User avatar

Joined: February 28th, 2013, 3:31 pm
Posts: 1806
I took a look at the GR research drivers and that is quite an interesting 12" driver and a good value. With 18mm Xmax it has a lot of linear volume displacement although the sensitivity is just OK. WIth the amps being used, that is of no consequence. The Qts is also slightly above .7 so if you used it in any way other than what they suggest, eg a closed box the QB would also be above optimim although with a servo system you could correct the bump you would get at resonance. There is no doubt that designng a sub with either a servo or other form of electronic compensation can make it easier to get the result desired.

One statement they make in their blurb is not totally correct. They say that in order to get a low Fs you need to have a heavy cone. Actually the Fs is a combination of the cone mass and the suspension compliance. If you have a light cone and very compliant suspension you can also get a very low Fs. However, the box size will have to be large or it will have to be used without a closed box otherwise in a small box the low air compliance will raise the Fb and also the Qb to levels that may be unacceptable. Everything is always a compromise.

Tom


Top
 Profile  
 
PostPosted: February 6th, 2016, 4:39 pm 
Offline
User avatar

Joined: January 13th, 2016, 9:14 pm
Posts: 870
The setup with the planar OB's and 4x12 servo subs.

Have all the modified ChipAmps running and setup with the digital crossover.


Attachments:
WP_20160130_001.jpg
WP_20160130_001.jpg [ 344.37 KiB | Viewed 78274 times ]
Top
 Profile  
 
PostPosted: February 8th, 2016, 6:26 pm 
Offline

Joined: March 5th, 2013, 9:35 am
Posts: 263
Location: Highland, MD
We can almost taste it! (Did I say that out loud?)

_________________
- Guy


Top
 Profile  
 
PostPosted: February 8th, 2016, 10:31 pm 
Offline
Site Admin
User avatar

Joined: February 28th, 2013, 10:38 am
Posts: 1705
Guy wrote:
We can almost taste it! (Did I say that out loud?)


I love the smell of sawdust in the morning. Smells like transconductance ;)

Roscoe

_________________
I can explain it to you, but I can’t understand it for you.


Top
 Profile  
 
PostPosted: March 6th, 2016, 2:21 pm 
Offline
User avatar

Joined: January 13th, 2016, 9:14 pm
Posts: 870
The servo amp boxes are flat packs. Glued the first one up today.


Attachments:
WP_20160306_002.jpg
WP_20160306_002.jpg [ 361.09 KiB | Viewed 78193 times ]
WP_20160306_001.jpg
WP_20160306_001.jpg [ 345.67 KiB | Viewed 78193 times ]
Top
 Profile  
 
PostPosted: March 9th, 2016, 3:36 pm 
Offline
User avatar

Joined: January 13th, 2016, 9:14 pm
Posts: 870
The two open baffle 6x12 servo sub array's are fully operational and sounding very good!

A good day for some pipe organ music!


Attachments:
WP_20160307_002.jpg
WP_20160307_002.jpg [ 313.32 KiB | Viewed 78179 times ]
Top
 Profile  
 
PostPosted: March 11th, 2016, 4:53 pm 
Offline

Joined: March 5th, 2013, 9:35 am
Posts: 263
Location: Highland, MD
Don't forget to tell us how they sound! That should push a lot of air around.

Do you have to worry about SAF? (Spousal Approval Factor) ;)

_________________
- Guy


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 393 posts ]  Go to page Previous  1, 2, 3, 4, 5, 6 ... 40  Next

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 22 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group