DCAudioDIY.com

DC Area Audio DIYer's Community
It is currently March 28th, 2024, 7:54 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 95 posts ]  Go to page Previous  1 ... 4, 5, 6, 7, 8, 9, 10  Next
Author Message
PostPosted: August 7th, 2018, 3:37 pm 
Offline

Joined: March 12th, 2013, 11:12 am
Posts: 738
No functional reason unless they mount other stuff in the same generic cabinet/chassis and could not fit all the additional ground leads on a single post?


Top
 Profile  
 
PostPosted: August 7th, 2018, 8:10 pm 
Offline
User avatar

Joined: January 15th, 2015, 7:19 am
Posts: 1697
Location: Baltimore MD
Yes maybe so that other models may have different configuration. I emailed the company and they would not send me a schematic. I would like to know what that weird ground symbol is about


Top
 Profile  
 
PostPosted: August 7th, 2018, 8:34 pm 
Offline

Joined: July 17th, 2016, 6:24 am
Posts: 1099
+
Attachment:
grounding.jpg
grounding.jpg [ 123.34 KiB | Viewed 10389 times ]


Top
 Profile  
 
PostPosted: August 8th, 2018, 8:38 am 
Offline
User avatar

Joined: February 28th, 2013, 3:31 pm
Posts: 1780
Here is a link to info I found on the dirrerence between a standard earth safety ground and a noiseless ground. In any case it appears that the symbol is not used properly in this isolation unit as both grounds are common.

http://www.aelgroup.co.uk/faq/faq008.php


Top
 Profile  
 
PostPosted: August 8th, 2018, 4:46 pm 
Offline
User avatar

Joined: January 15th, 2015, 7:19 am
Posts: 1697
Location: Baltimore MD
Thank Tom
I found the article very interesting since I was going to try circuit 2 and isolate equipment ground from house ground. I have done this before but found that it is against code to have two separate grounds and if one chooses to have multiple grounds they must be bonded.


Top
 Profile  
 
PostPosted: August 11th, 2018, 10:37 am 
Offline
User avatar

Joined: January 15th, 2015, 7:19 am
Posts: 1697
Location: Baltimore MD
I am finishing up my build but I have a question.
Pictures are a couple devices that are in series with the primary Load and Neutral
I first thought they were MOV but I thought MOV go accross between N and L
anyway here is the pic:

Attachment:
MOV_B.jpg
MOV_B.jpg [ 81.68 KiB | Viewed 10345 times ]


Top
 Profile  
 
PostPosted: August 11th, 2018, 10:50 am 
Offline

Joined: May 21st, 2017, 11:34 am
Posts: 27
Pelliott321 wrote:
Pictures are a couple devices that are in series with the primary Load and Neutral
I first thought they were MOV but I thought MOV go accross between N and L

These are NTC (negative temperature coefficient) thermistors. They limit the inrush current that can occur when you first power on a piece of equipment.
Here are a couple of links from the manufacturer of these parts that explains their properties and how they protect transformers.
---Gary

https://www.ametherm.com/surge-gard
https://www.ametherm.com/inrush-current ... rrent.html


Top
 Profile  
 
PostPosted: August 11th, 2018, 10:52 am 
Offline
User avatar

Joined: July 24th, 2015, 4:17 pm
Posts: 1701
Location: Parkville, Maryland
Pelliott321 wrote:
What I do not understand is the grounding scheme
Attachment:
iso3.jpg

what you see here is on the right post are ground wires for the input mains and the output sockets
what was on the left post was the ground(or shield) from the xformer.
Why did the manufacturer do this? What was gained?



I would expect that the one on the left in your image is the system ground and the one on the left is the safety ground bond.

_________________
Walt


Top
 Profile  
 
PostPosted: August 11th, 2018, 10:58 am 
Offline
User avatar

Joined: July 24th, 2015, 4:17 pm
Posts: 1701
Location: Parkville, Maryland
GaryB wrote:
Pelliott321 wrote:
Pictures are a couple devices that are in series with the primary Load and Neutral
I first thought they were MOV but I thought MOV go accross between N and L

These are NTC (negative temperature coefficient) thermistors. They limit the inrush current that can occur when you first power on a piece of equipment.
Here are a couple of links from the manufacturer of these parts that explains their properties and how they protect transformers.
---Gary

https://www.ametherm.com/surge-gard
https://www.ametherm.com/inrush-current ... rrent.html


I am not sure you want those devices in circuit. They will definitely raise the source impedance, which would not be an issue with computer electronics.

Besides, the surge is not going to be any more than the current draw of your goodies. You may also find that your power amps. will not perform as well when fed from the isolation transformer. Even my Carys don't like it and they only draw 3-amps. on a good day.

_________________
Walt


Top
 Profile  
 
PostPosted: August 11th, 2018, 1:09 pm 
Offline
User avatar

Joined: January 15th, 2015, 7:19 am
Posts: 1697
Location: Baltimore MD
Thanks for the info guys. I was hoping to determine that those device could be left out.
I just want the Felix filter on the mains side and duplex sockets on the load side


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 95 posts ]  Go to page Previous  1 ... 4, 5, 6, 7, 8, 9, 10  Next

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 55 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group