DCAudioDIY.com

DC Area Audio DIYer's Community
It is currently March 2nd, 2026, 4:55 am

View unanswered posts | View active topics


Board index » DCAudioDIY Main » Project Discussions

All times are UTC - 5 hours [ DST ]



Post new topic Reply to topic  Page 4 of 5
  [ 47 posts ]  Go to page Previous  1, 2, 3, 4, 5  Next
  Print view Previous topic | Next topic 
Author Message
Pelliott321
PostPosted: April 9th, 2017, 10:50 am 
Offline
User avatar

Joined: January 15th, 2015, 7:19 am
Posts: 1771
Location: Baltimore MD
Maggies back in and Carvers shelved until OPA4227 chips come in to see if high pass musicality improves.
The maggies are more polite but much more musical.
laptop in foreground is RealRTA showing pink noise from 10 to 20khz


Attachments:
Maggies04092017 copy.jpg
Maggies04092017 copy.jpg [ 274.42 KiB | Viewed 28483 times ]
Top
 Profile  
 
SoundMods
PostPosted: April 9th, 2017, 12:09 pm 
Offline
User avatar

Joined: July 24th, 2015, 4:17 pm
Posts: 1859
Location: Parkville, Maryland
You might want to install a DIP socket so you can change back. On paper the the TLO74 is a much better performer. After looking at the data sheets I have to wonder why someone would recommend the the OPA4227. ??? :confusion-confused:

_________________
Walt
Top
 Profile  
 
tomp
PostPosted: April 9th, 2017, 4:14 pm 
Offline
User avatar

Joined: February 28th, 2013, 3:31 pm
Posts: 1866
The OPA4227 is just an updated version of the OP27. It was a great OP Amp in its day and I built great MM and MC pre amps with the OP27 and OP37 a long time ago but there are better now. If you are looking at specs the LME49710 and LME49720 blow the OPA4227 away in almost every category. I am now using those in phono and line stages with great results.

Tom
Top
 Profile  
 
DaveR
PostPosted: April 9th, 2017, 6:48 pm 
Offline
User avatar

Joined: February 19th, 2017, 9:43 am
Posts: 539
My favorite audio op amps are the AD797 and LME49990. The AD797 can be hard to get stable depending on the circuit and the LME49990 isn't made any more. I don't believe there are any LME49990 available from an actual TI distributor. I'd be wary of sellers on eBay, especially if they happen to be located in China.

_________________
I have too much stuff - https://www.pleasebuymystuff.com
Top
 Profile  
 
tomp
PostPosted: April 9th, 2017, 6:58 pm 
Offline
User avatar

Joined: February 28th, 2013, 3:31 pm
Posts: 1866
I'm using AD797s in my custom preamp. They work well but the new LME series have no problems with stability. If I were going to build it now I would use the LME.

Tom
Top
 Profile  
 
Pelliott321
PostPosted: April 9th, 2017, 9:32 pm 
Offline
User avatar

Joined: January 15th, 2015, 7:19 am
Posts: 1771
Location: Baltimore MD
Now I am confused. kits claims the OPA is an upgrade and charge a lot for the chips. I can get them much cheaper from Digikey, etc so that's why I got the stock TL's. So this must have been just marketing BS.
In stalled sockets when I built the boards so I can roll chips, but now I will not waste my time with the OPA , but do not have a clue of what to try
Top
 Profile  
 
SoundMods
PostPosted: April 10th, 2017, 1:33 pm 
Offline
User avatar

Joined: July 24th, 2015, 4:17 pm
Posts: 1859
Location: Parkville, Maryland
Bummer! I did some window shopping and the best Quad Op-amps for high-end audio are surface-mounted devices. Texas Instruments especially had some audio goodies that they inherited from Burr Brown when they bought out Burr Brown. They also are not cheap.

_________________
Walt
Top
 Profile  
 
brombo
PostPosted: April 10th, 2017, 1:56 pm 
Offline

Joined: July 8th, 2016, 4:34 pm
Posts: 624
The following link may be of use for diy soldering of surface mount devices -

http://www.nutsvolts.com/magazine/artic ... _soldering
Top
 Profile  
 
SoundMods
PostPosted: April 10th, 2017, 3:43 pm 
Offline
User avatar

Joined: July 24th, 2015, 4:17 pm
Posts: 1859
Location: Parkville, Maryland
The problem here is that Paul's device(s) has quad op-amps in a dual-inline-plug (DIP) format. The DIP format, even though it has the same pin-out as the surface-mounted devices, is much larger.

I didn't do extensive shopping, but I did look at Analog Devices and Texas Instruments as my first go-to choices. There are numerous others such as Harris Semiconductor, Exar, Elantec, Signetics, National Semiconductor, etc.

_________________
Walt
Top
 Profile  
 
Roscoe Primrose
PostPosted: April 10th, 2017, 3:46 pm 
Offline
Site Admin
User avatar

Joined: February 28th, 2013, 10:38 am
Posts: 1732
SoundMods wrote:
The problem here is that Paul's device(s) has quad op-amps in a dual-inline-plug (DIP) format. The DIP format, even though it has the same pin-out as the surface-mounted devices, is much larger.


Adapters are available that you can solder the SMD to so it'll plug into the DIP socket....

Roscoe

_________________
I can explain it to you, but I can’t understand it for you.
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 4 of 5
  [ 47 posts ]  Go to page Previous  1, 2, 3, 4, 5  Next

Board index » DCAudioDIY Main » Project Discussions

All times are UTC - 5 hours [ DST ]

Who is online

Users browsing this forum: Google [Bot] and 30 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Switch to mobile style
Powered by phpBB® Forum Software © phpBB Group