DCAudioDIY.com

DC Area Audio DIYer's Community
It is currently March 28th, 2024, 7:08 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 16 posts ]  Go to page 1, 2  Next
Author Message
PostPosted: May 25th, 2016, 2:01 pm 
Offline
User avatar

Joined: December 14th, 2013, 2:19 pm
Posts: 948
Seeking advice, since I'm a digital moron. Yes Roscoe, I know.

Have a DAC that I'm pretty pleased with and have plans to mod. I've added a balanced AES/EBU input, but would like to eliminate that interface and go straight from USB to the DAC.

Any guidance is appreciated.

Stuart


Top
 Profile  
 
PostPosted: May 25th, 2016, 2:25 pm 
Offline
User avatar

Joined: January 13th, 2016, 9:14 pm
Posts: 787
Take a look at this if you have an I2S Bus input available on the DAC board:

http://www.amanero.com/

Usually it is the interface between the CS8414 and the DAC chip. It can also be used with Native DSD files if the DAC supports it.


Top
 Profile  
 
PostPosted: May 25th, 2016, 2:57 pm 
Offline
Site Admin
User avatar

Joined: February 28th, 2013, 10:38 am
Posts: 1682
As HAL kind of alluded to, you're going to bypass the 8414 if you go USB. Depending on your DAC, the 8414 MAY be configured to output I2S to whatever filter/DAC chip is next in the signal chain in your particular DAC. In addition to the piece HAL linked to, there are a whole boatload of CM6631A based USB-> SPIDF/I2S boards on ebay for <$30 that'll work fine, for a little more an XMOS asynchronous converter may be slightly better in performance. If your DAC isn't DSD capable, the extra money for the amenero board may not be worth it.

Of course, if your 8414 is SMT & soldered to the board, it's gonna be tricky, but not impossible, to modify the DAC to take the I2S input.

Roscoe

_________________
I can explain it to you, but I can’t understand it for you.


Top
 Profile  
 
PostPosted: May 25th, 2016, 3:40 pm 
Offline
User avatar

Joined: February 28th, 2013, 3:31 pm
Posts: 1780
I have both CM6631 and XMOS USB to SPDIF converters I'm not currently using if you would like to try them.

Tom


Top
 Profile  
 
PostPosted: May 26th, 2016, 8:14 am 
Offline
User avatar

Joined: December 14th, 2013, 2:19 pm
Posts: 948
Thanks for the input.

Tom, I'm going to pass on USB-S/PDIF. I have that now, would like to eliminate S/PDIF from the system.

Roscoe, HAL, if I understand correctly, the CS8414 serves to change the S/PDIF (in my case the balanced version) to the I2S protocol?

The DAC chips are BB PCM63. There are two other on board chips.

I don't have a super clear schematic. The DAC 60 is similar to my DAC 50, may be more legible.

Pictures are attached from when I replaced the Toslink input with a transformer, per Crystal's data sheet on the chip, to allow balanced input. Attaching both schematics. Will have to do multiple posts due to file attachment limits.

Attachment:
Output.jpg
Output.jpg [ 950.31 KiB | Viewed 28445 times ]

Attachment:
Overall.jpg
Overall.jpg [ 841.93 KiB | Viewed 28445 times ]

Attachment:
Receiver.jpg
Receiver.jpg [ 1.25 MiB | Viewed 28445 times ]



Does this help?

Stuart


Top
 Profile  
 
PostPosted: May 26th, 2016, 8:16 am 
Offline
User avatar

Joined: December 14th, 2013, 2:19 pm
Posts: 948
Attachment:
Lite_DAC50.jpg
Lite_DAC50.jpg [ 631.81 KiB | Viewed 28444 times ]

Attachment:
Small.jpg
Small.jpg [ 372.83 KiB | Viewed 28444 times ]

Attachment:
XFMR.jpg
XFMR.jpg [ 1.27 MiB | Viewed 28444 times ]


Top
 Profile  
 
PostPosted: May 26th, 2016, 8:17 am 
Offline
User avatar

Joined: December 14th, 2013, 2:19 pm
Posts: 948
Attachment:
dac60.JPG
dac60.JPG [ 689.48 KiB | Viewed 28445 times ]


This may be a bit more legible. But not exactly the same DAC. VERY close.


Top
 Profile  
 
PostPosted: May 26th, 2016, 8:23 am 
Offline
User avatar

Joined: January 13th, 2016, 9:14 pm
Posts: 787
As Roscoe points out, the CS8414 would need to be removed from the DAC pc board and the I2S Bus lines used with any of the USB to I2S Bus conversion systems.

Here is a link to the datasheet if needed to see the I2S Bus pins.

http://www.futurlec.com/Others/CS8414.shtml

I have a DAC60 and it has DF1704/PCM1704 DAC's. Had mine moded and still works.


Top
 Profile  
 
PostPosted: May 26th, 2016, 8:59 am 
Offline
Site Admin
User avatar

Joined: February 28th, 2013, 10:38 am
Posts: 1682
Looking at the DF1704 datasheet ( http://www.ti.com/lit/ds/symlink/df1704.pdf ), it looks like you might have issues with the XTI line on the DF1704, which is currently fed from the CS8414. Looks from the datasheet that the DF1704 can operate on it's own internal clock, but not at 96K. You'd need to change one or more control pins on the 1704 to make it run on it's own clock...

Roscoe

_________________
I can explain it to you, but I can’t understand it for you.


Top
 Profile  
 
PostPosted: May 26th, 2016, 9:15 am 
Offline
User avatar

Joined: December 14th, 2013, 2:19 pm
Posts: 948
Okay, the bulb is very dim, but it's starting to glow.

The I2S lines are pins 11, 12, 19 and 26. It appears that everything prior to that is associated with the 8414 and can safely be removed.

Ideally, I'd like to leave the S/PDIF and AES/EBU inputs in place and be able to switch between them and USB.

Can I simply cut traces, insert a switch or switch controlled reed relays, and add the USB/I2S interface?

It seems that several firms offer boards for this application, the Amanero one HAL linked to as well as Sonore and JL Sounds. The Sonore is a lot more money, but would be worth it if there is a big performance improvement.


Stuart


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 16 posts ]  Go to page 1, 2  Next

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: Google [Bot] and 32 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group